Barrel - Mono
Barrel Anchor Head is generally used in mono strand prestressing and tensile
testing machines.
Anchor Cone (Tube Unit)
Anchor Cone allows the transfer of prestressing force from the Anchor Head to the concrete segment. Anchor Cone guides the HT strand into the duct, facilitates
seating contact with the duct and gives free access to the injection of grout.
Anchor Cone is made of Cast Iron and is mainly used in prestressed concrete segments
and girders.
Technical Specification
| Sr. No. | Duct (code) | ID Inside Diameter(mm) | OD Outside Diameter(mm) | Wall Thikness(mm) | Compatible Anchor Cones |
|---|---|---|---|---|---|
| 1 | KTDSO (R) | 39 | 50 | 23+-405 | KTC 4KTIS |
| 2 | KTD63 (R) | 50 | 63 | Column #2 | KTS 7ETIS/ RTC AKTIS |
| 3 | KTD78(R) | 63 | 78 | Column #3 | Column #3 |
| 4 | KTD92(R) | 75 | 92 | Column #3 | Column #3 |
| 5 | KTD97(R) | 85 | 97 | Column #3 | Column #3 |
| 6 | KTD120(R) | 105 | 120 | Column #3 | Column #3 |
Anchor Head
Bearing Plate
Anchor Head gets located on the flat surface of the Anchor Cone & offers seating of wedges. Tapered holes in Anchor Head facilitate the seating of wedges and
holding the strands in stressed condition. Wedge holds the individual tensile element. The prestressing load is then transferred to the Anchor Head. Anchor Head is generally used in prestressed concrete segments and girders.
Technical Specification
| Sr. No. | Duct (code) | ID Inside Diameter(mm) | OD Outside Diameter(mm) | Wall Thikness(mm) | Compatible Anchor Cones |
|---|---|---|---|---|---|
| 1 | KTDSO (R) | 39 | 50 | 23+-405 | KTC 4KTIS |
| 2 | KTD63 (R) | 50 | 63 | Column #2 | KTS 7ETIS/ RTC AKTIS |
| 3 | KTD78(R) | 63 | 78 | Column #3 | Column #3 |
| 4 | KTD92(R) | 75 | 92 | Column #3 | Column #3 |
| 5 | KTD97(R) | 85 | 97 | Column #3 | Column #3 |
| 6 | KTD120(R) | 105 | 120 | Column #3 | Column #3 |
Technical Specification
Wedges
These are conical shaped components slitted in three equal parts and held together
around the strand by means of special wire circlips. Thread on the concave portion
of each slit holds the strand like a jaw and ensures proper locking after stressing.
Proper Hardening and tempering treatments are done to achieve superior quality
and strength.
Live Wedges
Live Wedges used for post-tensioning systems. Generally used in Girders, Slabs etc.
- Single Use Live Wedges
- Multi Use Live Wedges
| Density (IS 2530) | 0.94gm-0.94gm/Cm3 |
|---|---|
| Melt Flow Rate (MFR 190/5) ISO 1133 | 0.50gm+0.1gm/10Min |
| Coefficient of Thermal Expansion (For 20°c - 80°C) - DIN 53752 | 5 |
| Shore Hardness D (BS EN ISO 2039-1) | 3sec-60min 15sec-58min |
| Elongation at yield (DIN 53455) | 7% minimum |
Above specs are available in both single use & multi use line wedges.
Master Wedges
Master Wedges can be used multiple times and for heavy tensile systems. Generally
used in Pre-tensioning, Hydraulic Mono Jack, HT strand Tensile Test and ete.
Technical Specification - Anchorages System
Approved by
National Highway authority of India(NHAI)
Various Metro Corporation State Road Development Authorities
Tested and passed by 3rd Party Test Laboratories
Indian Institute of Technology (IIT) – Chennai
Anulab – Agra